Swing Cylinder Block Type Double Acting

IMPORTANT

• Actual clamping takes place only when the Cylinder has completed its 90 swing stroke.
• Clamping allowed only in clamping stroke not in swing stroke .
• Do not exceed max. flow rate. If flow rates are exceeded, swing cylinder indexing mechanism may be permanently damaged.

DESCRIPTION

The Block type design enables quick cylinder assembly and disassembly through horizontal and vertical mounting holes. Special threads are provided for vertical mounting operation. These double acting swing clamps are having special feature during rotation (swing) it covers 20mmstroke and there after it travels vertically for 10mm clamping stroke.

NOTE

• Refer general design notes before selection & use.
• CW Model dimensions are same asCCWmodel dimensions.
• Refer accessories sheet Page No. X2 for Clamp arm details.
• Given forces are for the standard arm lever. Pressure and flow should be reduced if clamp arm length is increased (Refer Graph Sheet Page No. G1).
• Ordering specification for seal kit. Add prefix "SK" to the model number.

FEATURES

• Forces given are axial forces. To obtain force at ‘F’ refer Graph Sheet Page No. G1.
• Min. / Max. Operating Pressure 10/250 bar. Large clamping range.
• Block type body design with symmetrical mounting hole layout.
• Total stroke 30 mm. Swing stroke 20 mm.Vertical stroke 10mm.
• Arm swing will be 90o± 2o.
• 360 adjustable arm location.(Special swing angles given optionally

Important

• If the system flow rate exceeds, use one way flow control valve in the upstream hydraulic lines.
• Length of Clamping arm, weight of Clamping arm, max. Permissible flow rate and working pressure are all important. Refer graphs for arm length and working pressure.
• Keep weight of Clamping arm to a minimum.

Block Swing Clamp Double Acting - Type 2

Important

• Actual clamping takes place when the Cylinder has completed its 90 swing stroke.
• Clamping allowed only in clamping stroke not in swing stroke.
• Do not exceed max. flow rate. If flow rates are exceeded, swing cylinder indexing mechanism may be permanently damaged.

DESCRIPTION

The Block type design enables for quick cylinder assembly and disassembly by means of horizontal and vertical mounting holes. These double acting swing clamps are having special feature during rotation (swing) it covers an internal stroke and swings horizontally for 90 stroke and there after travels vertically for10mmclamping stroke.

NOTE

• Refer general design notes before selection & use.
• CW Model dimensions are same asCCmodel dimensions
• For ClampArm details refer accessories sheet page No. X2.
• Given forces are for the standard arm lever. Pressure & flow should be reduced if clamp arm length is increased (Refer graph sheet page No. G1).
• Clamping Stroke is 10mm.
• Ordering specification for seal kit.Add prefix "SK" to the model Number.

FEATURES

• Min./ Max. Operating Pressure 30/100 bar.
• Large clamping range.
• Double acting ranges.
• Block type body design with symmetrical mounting hole layout.
• 360 adjustable arm location.
• Arm swing will be 90o ±2o
• Zero vertical stroke during 90 horizontal swing.

NOTE

• Refer general design notes before selection & use.
• CW Model dimensions are same asCCmodel dimensions.
• For ClampArm details refer accessories sheet page No. X2.
• Given forces are for the standard arm lever. Pressure & flow should be reduced if clamp arm length is increased (Refer graph sheet page No. G1).
• Clamping Stroke is 10mm.
• Ordering specification for seal kit.Add prefix "SK" to the model Number.

Important

• Compact design allows for efficient fixture design.
• If the system flow rate exceeds, use one way flow control valve in the upstream hydraulic lines.
• Length of Clamping arm, weight of Clamping arm, max. Permissible flow rate and working pressure are all important. Refer graphs for arm length and working pressure.
• Keep weight of Clamping arm to a minimum.